How To Clean Gears In A Hayward Blu

Rob is a puddle-service industry professional with over 20 years of feel.

Is your puddle vacuum moving slowly, or non at all? Read on.

Past Matthias Cooper, via Pexels, created with Canva

Is Your Hayward Navigator Pool Vacuum Not Moving?

A common pool cleaner is the Hayward Navigator, which consists of many moving parts. Occasionally, those parts fail and demand to be replaced.

Many puddle stores will repair these cleaners with no "labor costs," merely believe me, y'all will be paying more than enough for the parts and could save at least l% or more by ordering the parts online and fixing it yourself.

You don't need to be a rocket scientist to repair it. If yous take the fourth dimension to read through this article and refer to the photos, there really isn't much to information technology. Here are the troubleshooting tips you'll learn:

• Replacing parts
• Checking the A-frame
• Disassembling vacuum
• Checking the gearbox

Checking the feet or "shoes"

Rob Hampton

1. Determining What Needs to Be Replaced

If your navigator seems to spin around in circles without really going anywhere, or if it doesn't actually move at all, or if you've owned it for a while, yous probably already know that something may accept gotten stuck in the unit.

Y'all need to pull whatever information technology is out. (Surprisingly, this problem accounts for effectually half the calls I go.)

Next, take the unit out of the pool and check the "shoes" or "anxiety." These are the four pads that permit the cleaner to grip the surface. If these are worn down likewise much, they volition need to be replaced.

The A-Frame associates

2. Checking the "A-Frame"

The A-Frame is inside the navigator, but I tin can usually tell if it's bad by how loose the pods seem to exist. If there is a lot of play when you motion the pods dorsum and forth and information technology seems very loose, then the problem is probable to be the A-Frame.

The A-Frame is the most common function I supplant on these cleaners and doing and then is easy. The "pods" are unremarkably not bad unless they are visibly cracked or cleaved. Other parts include the turbine, bearings, and gearbox, which I volition talk well-nigh presently.

Checking the "pods"

Rob Hampton

Removing the screws

Rob Hampton

The turbine and bearings

Read More From Dengarden

3. Disassembling the Navigator

Please be sure to reference the photos for this department on how to disassemble your Hayward Navigator pool vacuum correctly.

How to Disassemble the Navigator

1. Remove the "wings" from the unit. The wings are attached to the pods.
2. Pry off the circular protector in the center of each pod, which will expose the screw heads. This volition crave a ¼ inch socket to unscrew.
3. After removing the 2 ¼ inch screws, the pods may still be on tightly. Pry with a flat screwdriver on either side of the screw and piece of work gently. The pods will come off.
4. Afterward the pods are removed, plough the unit of measurement upside downwards and remove the heart screw and remove the center slice, which that screw holds in. This will expose the turbine.
5. At present remove the 4 Phillips screws as shown in the photo. This will remove the department that houses the A-Frame. Remove the A-Frame gently and fix information technology aside.
6. Cease Here! If the A-Frame is the merely function that you are replacing, you lot will not need to go to the next pace and remove the six perimeter screws. You tin finish here and re-gather the unit with the new A-Frame.
7. In that location will now exist half dozen more screws effectually the perimeter of the unit. These are much longer than the first set of screws you removed. Y'all volition need to remove these to get to the turbine and bearings. Once screws are out, this piece will also exist removed fully exposing the turbine and bearings. The bearings and turbine will elevator out and the new bearing and turbine kit will go in its identify.
8. Lift the turbine and the two bearings out of place. Old bearings may fall autonomously. Don't worry, the new ones won't. Supersede with the new bearings and turbine. They tin can only go in ane way. Now replace the plate with the six screws. The turbine should spin freely.

4. The Gearbox

The gearbox does non often demand replacing. If it does, this is a very like shooting fish in a barrel office to supercede. With the vi perimeter screws, turbine, and bearings out, simply pull out the quondam one and replace it.

The gearbox

Reassembling Your Pool Vacuum

After replacing the parts, information technology is but a affair of re-assembling the unit only as it was disassembled. It's non hard since there aren't likewise many screws to remove and put back in.

If all was done right, it is ready to become back into the h2o and clean your pool!

This commodity is accurate and true to the best of the author's noesis. Content is for informational or entertainment purposes just and does not substitute for personal counsel or professional advice in business, financial, legal, or technical matters.

Questions & Answers

Question: I have had the Navigator for about two months, and its sucking, but non moving effectually the pool. Why is this?

Answer: If it's 2 months (brand new) it should exist under warranty if there's something broken. Exercise the pods move back and forth when it's non on the lesser? I would also check for any obstruction in the turbine (a stone, large leaf, etc...) These rarely go bad when they are that new unless you bought information technology used. Likewise bank check valve positioning on the puddle pump, meaning, does it have ENOUGH suction? If there's not enough suction, information technology won't motion much.

Question: My Hayward pool vac wasn't moving then I replaced the A-frame and turbine kit. It now simply stays in i department of the pool. No matter where I motion information technology, information technology always makes it style dorsum to the same department and does circles in that area. I replaced the gear box and medium turbine spindle gear final twelvemonth but I assume its one of these. Do you lot have whatsoever suggestions?

Answer: The pods might need to be replaced. Where the pods fit on to the A-frame can become loose over time, allowing for a lot of movement. They should fit snug. As well, check the rubber shoes to make sure they aren't worn downwardly.

Question: All of the inner parts of my Hayward Navigator pool vacuum are new; the pods and shoes are new, the hose is new. When the Navigator is suspended the pods motility. If I place the Navigator on the bottom of the pool all activeness stops. Do you have any suggestions?

Answer: The merely suggestion I would accept, knowing that you've replaced all the inner parts and pods, (otherwise, I'd say the A-frame or pods), would be to make sure in that location is plenty suction through the cleaner. If you accept a separate cleaner line, close the main drain valve and close the skimmer valve halfway and have the cleaner valve all the way open. Make sure filter is clean and the arrangement has plenty of menstruation. More suction on the cleaner will get in piece of work meliorate. You tin look at this article that explains how the valves should be set up.

https://dengarden.com/swimming-pools/How-to-Set-Va...

Question: One of the pods is jammed on my pool vacuum. How practice I get it off?

Answer: If the pod is hard remove, I normally use some wd-xl effectually it and a flat screw driver to work it off.

© 2022 Rob Hampton

Rob Hampton (author) from Port Richey, Florida on July 28, 2022:

Rob Tron. These are the kind of comments I love to see! I'm happy it worked out well. Thanks for reading!

Rob Tron on July 28, 2022:

Thank you then much! Your guide was very helpful. I bought new shoes since they were quite worn. I also ordered an A-Frame since you said it was so mutual to see it fail. And I am glad I did, since once I took the old one out, I saw 2 of the wheels I could turn by hand, merely non smoothly. The tertiary cycle didn't plow at all, and the fourth had lost all its ball bearings, so it was just a piece of plastic dangling on the axle. After replacing everything I put the cleaner back in the puddle and it worked! Thanks to yous I saved so much money buying but a few replacement parts!

Rob Hampton (author) from Port Richey, Florida on May 22, 2022:

Gary, brand sure in that location is plenty suction on the cleaner line. Be sure there are no breaks or leaks in any of the hose sections.

Gary on May 22, 2022:

I've replaced merely virtually everything on my navigator. When it's out of the water information technology will spin at the firm connection but when I place it in h2o it won't turn. Everything else is working fine.

Mauricio Batista on April 21, 2022:

Hi I would know if the house can crusade the problem for the navigator not moving or moving slowly? Thank you.

Rob Hampton (writer) from Port Richey, Florida on April 09, 2022:

Tom.. Thank you! I dearest comments like yours. I'm glad it worked well for you. Ya, I don't call back I've replaced a gear box, it's usually one of, or all of what you replaced. Should concluding for a few years for you!

Tom Roberts on April 09, 2022:

Great info, it gave me the backbone to endeavour the repair. I had to replace the turbine, pods, wings and A frame. Works similar new.

Thanks for posting this info.

Tom,

Rob Hampton (writer) from Port Richey, Florida on February 19, 2022:

John (and anyone else) I've now enabled the "enquire the author a question" Please post questions nether that platform but also experience free to get out comments here. John..The parts you replaced should final much longer than a few months. Without being able to physically check out the cleaner, hard to say. Gear box? Peradventure. A lot of dissimilar issues could cause it to spin in circles. Check the pods and "shoes"

john on February 19, 2022:

So, I have replaced all the inner parts,and it worked for a few months now it gets stuck. I notice it doesnt pass the hang test and the main plastic gear that the hose hooks upward to gets stuck and will move a little bit in 1 direction but not the other, My thoughts is maybe the main gear is worn out. Whatsoever thoughts?

Rob Hampton (author) from Port Richey, Florida on October xi, 2022:

Hi Rebecca. Yes, replace all iv. These can exist purchased on Amazon. A local puddle supply store will have them, but you lot'll pay 4 times as much.

Rebecca on October xi, 2022:

I just looked at my Hayward and see the feet are worn down and the back ones are gone. Where can I get theses and practise I take to supervene upon all four of them

Rob Hampton (writer) from Port Richey, Florida on July 02, 2022:

Sorry for the filibuster Robert. I'll exercise my best hither. And then..should the gear cone spin freely? No. It should be pretty tight and accept some "try" to turn by hand. Sounds like you've washed everything right and then far although you did not mention a pod replacement. Pods can have new "feet" simply frequently where they are placed on the a-frame, that connection or piece where the pod screws into the cleaner can exist worn.. IE; gaps causing it to sideslip. Gear "grinding" racket? Depends on what you mean. Yeah, information technology's normal when the cone is turned to make a sound. More than like gears moving rather than "grinding". The valve positioning... You mentioned the fountain.. That is on the return side of the pump and so doesn't have anything to practice with the amount of suction on the cleaner. Not certain how the intake side of your pump is set.. But should be... SKIMMER/Main DRAIN/CLEANER (peradventure spa if a combo pool/spa but spa should be closed anyway if in normal puddle mode) Valves should exist (on intake side)... Master drain closed completely. Cleaner fully opened and skimmer open one-half manner. Arrange only the skimmer valve for more or less suction on the cleaner. Promise this helps

robert miliano on July 01, 2022:

i have a pebble tech pool and a hayward navigator pool cleaner. a hayward DE filter organisation.. the cleaner would not move from the centre of the pool .. i replaced nearly everything(shoes,a frame associates, turbine and bearings , gearbox associates, the intermediate gear and spindle gear and spindle,front and rear flap.. the just thing i hadn't put into this $$$ pit was the cone gear.. is the cone gear suppose to turn freely ...??

its stiff and makeS a grinding noise.. i looked at the teeth to encounter if whatsoever were missing or out of shape but they announced to exist ok... i used the vac gauge and information technology said max.... i don't know how to set up the valve handles for skimmer and water fall.. Aid!!!

Source: https://dengarden.com/swimming-pools/navigatorrepair

Posted by: hunterloomes.blogspot.com

Share this post